With X problems facing you daily, trying to protect your water sources, TUFF CAGE is here to help. With over 15 years of experience, lots of research and development has been done to develop and design a Backflow Protection Security Enclosure that would meet your needs, enhance the environment and save you money. Tuff Cages are our answer to residential units. Uses 1” Metal tubing with 16ga diamond mesh. A little less rugged, and good for those less traveled areas. The Ultimate Tuff Cage is used for Commercial applications, and high traffic areas. These cages are sold by measurements since what is inside matters for space. These are also used for Gas valves, electric boxes, etc., anything anyone wants to protect from theft and vandals.
USING OUR HEAVY DUTY HARDWARE PINS
is used when there is a cement slab already in place.
used with our standard cages, UTC -.05 –
UTC-3.3 and TC-.05-TC-3.3 Cages.
cage over the equipment you will be securing.
Locate the hole in the Cage Lock box, 2 pins for lift-off units, and
mark thru the hole where you will want to place the 2 piece Dry Install pin
(s). Remove cage and where you put a
mark, Drill 5/8” hole in the correct center line to the holes on the bottom of
anchor piece into drilled holes. (Dry install pins come in 2 pieces, top screws
off) We recommend putting epoxy into the hole before you place the bottom part
of the locking pin. Use center punch and hit with hammer to lock anchors into
place. Then screw in the top locking pin
into the correct position. (When you set the cage on pin, you should see the
hole in Locking pin.) Now place the cage
unit onto the top of the Heavy Duty Locking Pins and place your locks through
the hole in the heavy duty locking pin.
grade around backflow assembly construction. Set up form around established
backflow assembly, tape expansion foam or tape around pipes. After you mix and pour concrete into your
form, level concrete, put Heavy Duty Locking Pins into white template, if
appropriate, cages with hinges will not include a template, please place hinged
cage close to one of the backflow pipes to ensure there is enough radius
clearance to allow cage to be opened. Hole in pin must be facing out. For lift
off cages make sure hole in Heavy Duty Locking Pins is facing the black dot on
white template. (Pins should be
inserted into wet cement to insure proper installation placement.) Work bottom of Heavy Duty Locking Pins (while
in template) into wet concrete. When
set, level cage in concrete, carefully
remove white template.**
concrete is fairly firm, place the cage onto the top of the Heavy Duty Locking
Pins and place your locks through the hole in the heavy duty locking pin.
NOTE: After removing white template,
please check how the cage sets on the pins, a slight adjustment may be needed
to be made.
Let Us Protect You With This
Experience and Excellence, It's the
Foundation of everything we do. With the most experienced fabricators and
designers, we apply our extensive design knowledge and experience to every
project we do.
OUR CUSTOM PROJECTSWe
know how everyone is on a budget and when theft occurs, your business
is impacted and sometimes closed down until the repairs are made. It
costs money to make repairs and replacements. We provide the security
needed for you to keep your resources.
Please contact us for custom made cages 928-521-4725, or email.
Backflow Theft Prevention-"ALWAYS ON GUARD"©-WE PROTECT YOUR BACK©REMEMBER-PREVENTION COSTS LESS THAN REPLACEMENT©DON'T BE EXPOSED - GET ENCLOSED©
Small Backflow Cage – TC-.05 – Internal dimensions – 10.5”Wx 18”Hx 15.5”L Medium Backflow Cage – TC- 1 – Internal dimensions – 10.5”Wx 24”Hx 22.5”L Large Backflow Cage – TC2 – Internal dimensions – 10.5”Wx 24”Wx 30.5”L XLarge Backflow Cage _ TC-3.3 Internal dimensions – 10.5”Wx 30”Hx 36”L